array(2) {
["Article"]=>
array(10) {
["id"]=>
string(3) "379"
["member_id"]=>
string(3) "102"
["title_eng"]=>
string(20) "Streaking Grime Test"
["title_hrv"]=>
string(58) "Testiranje efekta prljavštine koja curi (Streaking Grime)"
["mask_eng"]=>
string(20) "streaking_grime_test"
["mask_hrv"]=>
string(55) "testiranje_efekta_prljavstine_koja_curi_streaking_grime"
["content_eng"]=>
string(3337) "
I’m planning two larger projects at the moment - firstly a diorama involving a slightly converted Mortisan Boneshaper from the Ossiarch Bonereapers Age of Sigmar faction raising a bunch of skeletons from their graves, and secondly my own converted warband for the game Forbidden Psalm. Both projects have in common that I want to do them in a sort of Grimdark aesthetic, and so I decided to play around with Streaking Grime. To make sure I don’t ruin the big projects though, a test is necessary.
I’ve had this 3D-printed General Grievous (courtesy of Kiki - thanks Kiki) lying around for a while, and it’s a good test model. The fact that it’s 3D-printed is a positive, as the details are less crisp than with Legion or Shatterpoint models. This will put Streaking Grime’s capabilities to the test, and I’ll see if it flows into the somewhat superficial recesses as well as oils or other washes. First I gave the model a few quick base coats, as well as a coat of matte varnish.
Then I used a cheap synthetic brush to cover the whole model in the Streaking Grime. I left this for 15 minutes.
Recently I found some nice makeup remover brushes at DM, that doesn’t leave any cotton hair on my model as Q-tips tend to do. So I covered one side of this makeup remover with Enamel Odourless Thinner, and left the other side dry. I started with the dry side, removing the surface layer of Streaking Grime from the top parts of the model. Then I used the side with the thinner to remove more Streaking Grime. Eventually I used the same cheap, synthetic brush dipped in the Odourless thinner, to remove even more Grime from the hard to reach places. After just a few minutes of removing the enamel, I had this:
I like how the Streaking Grime washes and weathers my model in one coat, and the tint it gives to colours, especially beiges tones, appeal to me. After a few quick, simple edge highlights, I had this result:
Except for basing and the lightsabers, it’s pretty much finished. All in all this model took me under two hours of painting, and I’ve decided I like the result. I’m going to be using this technique again in my two upcoming projects. Another article with updates on the progress on my Skeleton diorama will follow soon.
"
["content_hrv"]=>
string(3324) "
Trenutačno planiram dva veća projekta - prvo dioramu koja uključuje malo preuređenog Mortisan Boneshaper iz frakcije Ossiarch Bonereapers Age of Sigmar koji podiže hrpu kosture iz njihovih grobova, a kao drugo moj vlastiti preuređen crew za igru Forbidden Psalm. Oba projekta imaju zajedničko to što ih želim raditi u nekoj vrsti Grimdark estetike pa sam odlučio poigrati se sa Streaking Grimeom. Kako bih bio siguran da neću uništiti velike projekte, test je bio neophodan.
Ovaj 3D isprintani general Grievous (hvala Kiki) ležao je neko vrijeme, stoga je postao dobar testni model. Činjenica da je ispisan 3D je pozitivna, jer su detalji manje oštri nego s modelima Legion ili Shatterpoint. To će dobro testirati metodu sa Streaking Grimea i vidjet ću hoće li se slijevati u udubine kao i ulja ili druga sredstva za pranje. Prvo sam modelu nanio nekoliko brzih temeljnih slojeva, kao i sloj mat laka.
Zatim sam jeftinim sintetičkim kistom pokrio cijeli model u Streaking Grime. ostavio sam da se suši 15 minuta.
Nedavno sam u DM-u našao lijepe kistove za skidanje šminke, koji ne ostavljaju dlake od pamuka. a što metoda sa štapićima za uši ima tendenciju učiniti. Stoga sam jednu stranu ovog sredstva za skidanje šminke prekrio Enamel Odourless Thinnerom, a drugu stranu ostavio suhom. Počeo sam sa suhom stranom, uklanjajući površinski sloj Streaking Grime s gornjih dijelova modela. Zatim sam upotrijebio stranu s razrjeđivačem uklanjajući višak Streaking Grime. Na kraju sam upotrijebio isti jeftini, sintetički kist umočen u Odourless Thinner, a uklanjanje još više prljavštine s teško dostupnih mjesta. Nakon samo nekoliko minuta skidanja ovo je bio rezultat:
Sviđa mi se kako Streaking Grime pere i njeguje moj model u jednom sloju i nijansu koju daje, posebno bež tonovi. Nakon nekoliko brzih, jednostavnih isticanja rubova, dobio sam ovo:
Osim baze i svjetlosnih mačeva, prilično je gotovo. Sve u svemu ovaj model me oduševio dva sata bojanja i odlučio sam da mi se sviđa rezultat. Ponovno ću koristiti ovu tehniku u moja dva nadolazeća projekta. Još jedan članak s novostima o napretku moje diorame s kosturom slijedi uskoro.
"
["created"]=>
string(19) "2024-04-06 18:08:45"
["modified"]=>
string(19) "2024-04-07 17:22:06"
}
["Member"]=>
array(10) {
["id"]=>
string(3) "102"
["group_id"]=>
string(1) "2"
["first_name"]=>
string(9) "Sebastian"
["last_name"]=>
string(8) "Søgård"
["first_name_mask"]=>
string(9) "sebastian"
["last_name_mask"]=>
string(4) "sgrd"
["username"]=>
string(5) "norge"
["password"]=>
string(40) "4dea770e7045a97695c7dc529698e85f5dadbded"
["born"]=>
string(19) "2003-01-21 09:03:00"
["created"]=>
string(19) "2022-01-21 09:03:12"
}
}